IMRE MCQ Pdf – नमस्कार दोस्तों आज की इस Post मे हम आपको IMRE के Top 100 ऐसे IMRE MCQ Pdf Provide करने वाले है जो कल Exam मे आ सकते है बस आपसे यही कहूँगा एक बार इस Post को जरूर पढ़ ले
यदि आपने इस Post को एक बार भी पढ़ लिया तो आपको ये idea मिल जाएगा की इस post मे कौन से Question है और क्या इनमे से कोई Question Exam मे आया है या नही ।
यहाँ पर दिये गए सभी Mcq का पीडीएफ़ आपको telegram channel पर मिल जाएगा ।

IMRE MCQ Pdf Start Now
1.Which material can be used upto a temperature of 130 degrees celsius?
● Mica
● Cotton
● Synthetic resin
● All of these
Ans-A
2. Which alloy is used as electrical resistance alloy?
● Nickel alloys
● Nickel chromium alloys
● Ferro nickel alloys
● Only a and b
● All of these
Ans – E
3. What is the purity of electricity graded aluminium?
● 95%
● 98.3%
● 99.5%
● 97.5%
Ans-C
4. What is meant by Equaliser bus?
● The best connecting series fields in parallel
● The bus connecting series fields in series
● The bus connecting shunt fields in parallel
● The best connecting shunt field in series
Ans-A
5. Which among the following application uses ward Leonardo method of speed control?
● Rolling mills
● Collierty windings moter
● Lifts and elevators
● Only a) and b)
● All of above
Ans – E
6. Which type of enclosure is provided for DC Motors used in coal handling plants?
● Screen Protected
● Open type
● Totally enclosed fan cooled
● Drip proof
Ans-C
7. which among these is the application of Universal Motors?
● Vacuum cleaners
● Fans
● Hair dryers
● Washing machines
Ans -A
8. What is the typical value of the capacitor is used in Capacitor start capacitor run induction motor?
● 5micro F
● 40 micro F
● 300 micro F
● 1000 micro F
Ans-C
9. What is the use of current transformer?
● Stepping up AC current
● Measuring and protection
● Stepping down AC current
● Both B and C
● All of these
10. At what angle difference in the main winding and the start winding separated in a split Phase capacitor start induction motor?
● 45 ° Electrical
● 90° Electrical
● 45° Electrical
● 90° mechanical
Ans-B
11. What material is used for the manufacture of brushes in DC Motors?
● Lead
● Copper
● Graphite
● All of these
Ans- C
12. Which among these devices are used to protect low voltage induction motor?
● HRC fuse
● Contactor starter
● Thermal overload relay
● All of these
Ans – D
13. Tap changing Transformer are used for?
● Stepping up the voltage
● Stepping down the voltage
● Both stepping up and stepping down the voltage
● Supplying low voltage current power instruments
Ans-C
14. An ammeter is a ….. instrument?
● Absolute instrument
● Secondary instrument
● Recording instrument
● Integrating instrument
Ans- B
15. For what voltage is twin conductor bundle used in India?
● 220 KV
● 330 KV
● 500 KV
● 750 KV
Ans – C
16. Which of the following machine will be preferred to charge the batteries?
● Series motor
● Shunt generator
● series generator
● Shunt motor
Ans – C
17. Which of the following motor in used in ceiling fan?
● Universal motor
● Induction motor
● Series motor
● Synchronous motor
Ans – B
18. Electrostatic voltmeter instruments are suitable for?
● AC work only
● DC work only
● Both AC and DC work
● None of these
Ans-C
19. The failure percentage of electric motor is higher due to?
● Insulation failure
● Overloading
● Bearing failure
● None
Ans- C
20. Which of the following is usually not the generating voltage?
● 6.6 KV
● 9.9 KV
● 11 KV
● 13 .2 KV
Ans – B
21. In how many types of transformer can be used with relay protection system?
● 5
● 10
● 2
● Many
Ans – C
22. Ingress of air into the oil tanks and be avoided by using?
● Relays
● Plastic coatings
● Metal coatings
● Fuses
Ans – A
23. When tripping of the transformer from the main ckt is required?
● Local overheating
● Salt circuited Core laminations
● Core Bolt insulation failure
● Function of bushings
Ans – D
24. Transformer used generally don’t belong to type instruct and forget?
● True
● False
Ans – B
25. Which of the following is the region relating to the maintenance while operation?
● To obtain the maximum practicable operating efficiency
● To obtain optimum life
● To minimise the risk of premature and expected failure
● Maximum efficiency, life, minimum temperature
Ans – D
26. Stored oil should be checked in continuously for?
● Impurities in the oil
● Oil level
● All moisture content
● Oil Reactions
Ans – C
27. Dissolved gas content are need to be observed because?
● Dissolved oxygen
● Dissolved gases from outside air
● Dissolved gases from arcs occurring in the Transformer
● All dissolved gases
Ans – C
28. How many places of our content possible?
● 4 places
● 5 places
● 8 places
● 2 places
Ans – A
29. What is the advantage of gas monitor?
● Time delay
● Alarms at presence of a particular gas
● Less efficiency
● Requires high power
Ans – B
30. For High really reliability of Transformer action ,how many fundamental checks should be done?
● 2
● 3
● 4
● Can’t tell
Ans- B
31. Which of the following material are not used for the Transmission and distribution of electrical power?
● Copper
● Aluminum
● Tungsten
● Steel
Ans- C
32. By which of the following method electric power may be transmitted from one location to another location?
● Underground System
● Over head system
● Both a and b
● None of the above
Ans – C
33. Which of the following transmission line have more essential cost?
● Overhead transmission
● Underground transmission
● Both Have almost the same initial cost
● None of the above
Ans – B
34. Name the Cable or connector which connects the distributor to the consumer terminal?
● Service mains
● Distributor
● Feeders
● None of the above
Ans – A
35. The usual spans with R. C. C. Poles are? ( important)
● 40- 50 m
● 60-100 m
● 200-300 m
● 80-150 m
Ans – D
36. Which of the following are the constants of the transmission lines?
● Inductance
● Capacitance
● Resistance
● Conductance
● All of above
Ans – D
37. Low tension cables are meant for use up to?
● 1kv
● 5kv
● 10kv
● 33kv
Ans – 1KV
38. The operating voltage of High Tension cables is upto?
● 1-11kv
● 11-20kv
● 11-33kv
● Above 33kv
Ans – A
39. The operating voltage of super tension cables is?
● 1-11kv
● 11-33kv
● 33-60kv
● Above 66kv
Ans – B
40. Ionization in circuit breaker facilitated by?
● Increase of field strength
● Increase of mean free path
● High temperature
● All of above
Ans – D
41. Arc interruption is done by?
● High resistance interruption
● Low resistance interruption
● Both a and b
● None of these
Ans – C
42. Part of circuit breaker helpful in Breaking the current is?
● Trip coil
● Contacts
● Handle
● Medium
Ans- B
43. Desired fitting of a circuit breaker is?
● Manually
● Automatically
● That it should give warning
● None of these
Ans – B
44. Arcing time is the time between?
● Separation of circuit breaker and extinction of Arc
● Separation of circuit breaker and right of recovery voltage
● Normal current interruption and arc extinction
● None of these
Ans – A
45. For single frequency transients, ratio of peak restriking voltage to time between voltage zero and peak voltage is called?
● Restriking voltage
● Recovery voltage
● Rate of rise restriking voltage
● Active recovery voltage
Ans – C
46. Time between energisation of trip coil and separation of contacts is called?
● Closing time
● Opening time
● Both a and b
● None of tthese
Ans – D
47. In circuit breaker, to facilitate arc quenching,dielectric strength can be increased by
● Lengthening of the gap
● Cooling
● Blast effect
● All of above
Ans – D
48. Rate of right restriking voltage depends upon?
● Active recovery voltage
● Natural frequency of oscillation
● Both a and b
● Rating of circuit breaker
Ans – C
49. Which switch is used for the automatic control of the motor?
● Hand off auto switch
● Hand on auto switch
● Rheostatic switch
● Any of the above
50. ……are non-manual condition control switches activated by an unsafe condition?
● Switches
● Gear
● Interlock
● None of these
Ans – C
51. Typically , interlocks stop motors….. but do not start Motors… .
● Manually, automatically
● Automatically , manually
● Automatically , automatically
● Manually , manually
Ans – C
52. The DC shunt motor is running with a certain load .The effect of adding an external resistance in field curuit is to :
● Increase the motor speed
● Stop the moter speed
● Reduce the motor speed
● Reduce the armature speed
Ans- A
53. The three point starter can be used for?
● Both shunt and compound motor
● Shunt Moter only
● Series Moter only
● Compound Moter Only
Ans- A
54. DC motor is recommended for the locomotive drive is?
● DC series motor
● DC long shunt compound motor
● DC shunt motor
● Dc short Shunt compound motor
Ans – A
54. In the case of a 3 phase induction motor Plugging is done by
● Starting the motor on load which is more than the rated load
● Pulling the motor directly on line without a starter
● Interchanging connections of any two phases of the starter for quick stopping
● Locking of the rotor due to harmonics
Ans – C
55. The earthing Rod orientation in the pit should be
● 45° degree
● Horizontal
● Vertical
● 75°
Ans :- C
56. Ground resistance value for sensitive installation is?
● Less than 5 Ohms
● 5-25 ohms
● 50 ohm
● 100 ohms
Ans – A
57. Statement : which one of the following is used in earth pit?
● Aluminium and iron
● Graphite and silver
● Graphite and magnesium
● Salt and charcoal
Ans :- D
58. The thickness of metallic shielding on cables is usually?
● 0.04mm
● 0.2 to 0.4 mm
● 3 to 5 mm
● 40 to 60 mm
Ans :- A
59. . ……Cables are used for 132 KV lines?
● High tension
● Super tension
● Extra high tension
● Extra super tension
Ans :- D
60. PVC stand for
● Polyvinyl chloride
● Post varnish conductor
● Pressed and varnished cloth
● Positive voltage conductor
Ans – A
61. A certain cable has an insulation of relative permeability 4.If the insulation is replaced by one of relative permeability 2 , the capacitance of the cable will become
● One half
● Double
● Four times
● None of the above
Ans – A
62. High Tension cables are generally used upto
● 11kv
● 33kv
● 66kv
● 132kv
Ans – A
63. The material for armouring on cable is usually
● Steel tape
● Galvanized steel wire
● Any of the above
● none of the above
64. Which of the following protects a cable against mechanical injury
● Bedding
● Sheath
● Armouring
● Any of the above
65. The unit of dielectric strength is
● V/m2
● MV/m2
● MV/m
● Vm
Ans – C
66. If the voltage increases, what happens to dielectric strength?
● Increases
● Decreases
● Remains the same
● Becomes zero
Ans – A
67. If the thickness of the material increases what happens to the dielectric strength?
● Increases
● Decreases
● Remains the same
● Becomes zero
Ans – B
68. Which medium has the highest dielectric strength?
● Water
● Mica
● Air
● Glass
Ans – C
69. Which of the following is not a material handling equipment?
● Cranes
● Lifts
● Tongs
● Hoists
Ans – C
70. What is the ratio of Preventive maintenance and total maintenance in general manufacturing industry?
● 1:10 men
● 1:2.69 men
● 1:2.37men
● 1:3.77 men
Ans – A
71. Frequency of inspection is decided on the basic of overloading
● True
● False
Ans- A
72. A safety electrical one line diagram should be used to…….all sources of electrical energy
● Identify
● Castigate
● Evaluate
● Modify
Ans – A
73. The minimum allowable work space around electrical equipment is…….inches Deep
● 36
● 48
● 24
● 30
Ans – D
74. Which is the’ can’t let go” range of current flow?
● 3-9 ma
● 9-25 ma
● 25-60 ma
● 1-3 ma
Ans – B
75. megger is a
● Source of emf
● Source To measure high resistance
● Type of a null detector
● Current carrier
Ans – B
76. Megger is also used for
● Providing additional EMF
● Bridge balance
● Testing insulation resistance
● Controlling the temperature
Ans – C
77. Megger works on the principle of
● Kirchoff’s current laws
● Ohm’s law
● Gauss’s law
● Electromagnetic induction
Ans – D
78. The role of the permanent magnet in a megger is to
● Providing field
● Provide voltage
● Generate power
● Balance the circuit
Ans – A
79. A guard ring is provided in a megger to
● Protect the circuit
● Eliminate error
● Reduce current flow
● Limit the temperature rise
Ans – B
80. The supply to be megger is given by
● AC motor
● AC generator
● permanent magnet DC motor
● DC generator
Ans – C
81. The moving element of the ohmmeter in a megger consists of
● 1 coil
● 4 coil
● 3 coil
● 10 coil
Ans – C
82. The role of the compensating coil in a megger is
● Reduce current
● increases voltage
● control temperature
● scaling
Ans – D
83. The earth resistance can be measured by
● Fall off potential method
● Using an Earth tester
● Ducter ohmmeter method
● only a and b
● all the above
Ans – D
84. Electrical equipments are generally Earthed through an electrode to avoid socks when someone touches the body of the equipment . the earth resistance is effected by
● Depth of electrodes buried in the soil
● Shape and material of earth electrodes
● Specific resistance of the soil surrounding the electrode
● All of these
● None of these
85. For the measurement of low resistance from few ohms down to one microohm, which of the following instrument is not suitable?
● Potentio meter method
● Ammeter – voltmeter method
● Ohmmeter
● Kelvin double bridge method
Ans – C
86. The method/methods suitable for the measurement of low resistance is/ are
● Ammeter – Voltmeter method
● Kelvin’s double bridge method
● Potentiometer method
● All of these
87. Which DC motor will be suitable along with flywheel for intermittent light and heavy loads?
● Series motor
● Shunt motor
● Comulatively compound Moter
● Differentially compounded moter
Ans – A
88. The hysteresis loss in a DC Machine least depends on
● Frequency of magnetic reversals
● Maximum value of flux density
● Value and grade of iron
● Rate of flow of ventilating air
Ans – D
89. The ratio of starting torque to full load torque least in case of
● Series motors
● Shunt Motors
● Compound motors
● None of the above
Ans – B
90. For which of the following applications a DC motor is preferred over an Ac motor
● Low speed operation
● High speed operation
● Variable speed operation
● Fixed speed operation
Ans – C
91. The armature voltage control of DC motor provides
● Constant voltage drive
● Constant current drive
● Constant torque drive
● None of the above
Ans – C
IMRE MULTIPLE QUESTIONS